External Recess/Ceiling Mount Microwave Sensor
The Merrytek External Recess/Ceiling Mount Microwave Sensor is a compact, ceiling-recessed motion detector that controls LED fittings automatically – light on when someone enters, held on while they’re there, off after a set period when they leave.
Three DIP switches let the installer dial it in on site – detection sensitivity (25, 50, 75 or 100%), hold time (5 seconds, 1 minute, 5 minutes or 10 minutes) and daylight threshold (5, 30 or 50lux, or always-on). One sensor covers everything from a small washroom to a large open-plan office.
It drops into a 55mm ceiling cut-out alongside our downlights, sits flush with the ceiling, and wires directly into the LED driver.
Key Features
- 5.8GHz microwave detection - wider, more reliable coverage than a PIR sensor
- 120° detection angle, 6m max. range
- Selectable detection sensitivity (25% / 50% / 75% / 100%)
- Selectable hold time (5sec / 1min / 5min / 10min)
- Daylight sensor threshold (5lux / 30lux / 50lux or Disabled)
- Compatible with LED Recessed and Slim Downlights
Compatible with
What we get asked
What is a ceiling mount microwave sensor?
A ceiling mount microwave sensor is a small device that sits flush in the ceiling and switches an LED fitting on automatically when it detects movement, then switches it off again after a set time of no movement. Ours uses microwave detection rather than the more common PIR (passive infrared), which gives wider, more reliable coverage in spaces with partitions, curtains or other obstructions.
What's the difference between a microwave sensor and a PIR sensor?
A PIR sensor detects body heat – it works well in line-of-sight but can be blocked by glass, curtains or thin walls. A microwave sensor sends out a low power radio signal at 5.8GHz and detects movement from how that signal bounces back. The advantages: it sees through non-metallics materials, has a wider effective area, and doesn’t need a direct line-of-sight to a warm body. The trade-off is that microwave can also pick up movement outside the intended area (through a thin wall, for example) if the sensitivity is set too high – that’s why ours has four sensitivity settings to dial it in.
What does the sensor detect, and how far does it reach?
It detects movement within a 120° cone below the sensor, with a maximum range of 6m. Effective reach depends on the sensitivity setting (25%, 50%, 75% or 100%), which you match to the room: 25-50% for a washroom or a short corridor, 75% for a meeting room, 100% for a large open office.
How do you adjust the sensor - sensitivity, hold time and daylight threshold?
Three DIP switches on the side of the sensor set everything on site – no remote, no app, no separate controller:
Detection sensitivity – 25%, 50%, 75% or 100% of full range. Match it to the room size.
Hold time – 5 seconds, 1 minute, 5 minutes or 10 minutes. This is how long the light stays on after the last detected movement.
Daylight threshold – 5lux, 30lux, 50lux or Disabled. The sensor only triggers the light when ambient light is below this level. Set “disabled” for areas where the light should come on regardless of daylight; set 50lux for offices with decent natural light, where you only want artificial light kicking in when it’s gloomy.
How many LED fittings can one sensor control?
The sensor handles up to 800W of resistive load or 400W of inductive load. In practical terms, that’s a serious number of LED fittings: most modern LED downlights draw 10-30W each, so one sensor can comfortably control a full corridor, classroom or open office before you need a second one. If you’re approaching the limit, give us a call and we’ll work through the numbers with you.
What size cut-out does the sensor need, and what's the ideal mounting height?
The sensor drops into a Ø55 circular cut-out – so it sits flush with the ceiling without standing out. The ideal mounting height is 2.5m to 4m, which covers standard ceiling height for most commercial interiors.
Which LumiRetro fittings is this sensor compatible with?
The sensor controls our LED Recessed Downlights and LED Slim Downlights. If you’re working with a specific fitting and want to confirm, send us the part number and we’ll check.
Can the sensor be used with other brands?
We test the sensor with our own LED fittings, so we can’t guarantee it’ll work with luminaires from other manufacturers.
Can the sensor be used outdoors or in damp areas?
No – the sensor is IP20 rated, which means it’s protected against tampering and dust but not against water. It’s strictly an interior product. If you need a prescence sensor for an external install or a damp area, give us a call and we’ll point you to an IP-rated alternative.
Do I need an electrician to install the sensor?
Yes. The sensor wires into the mains supply, so installation should always be carried out by a qualified electrician in line with current wiring regulations.
What's the warranty on the sensor?
The sensor comes with a 3 year warranty for reliable performance across the life of the install.

