Suspension Kit
Suspension kits for hanging out LED panels from fixed ceilings – anywhere there’s no ceiling grid to drop into. Brackets fix to the back of the panel using its existing screws; the wires feed through, lock with a push-button mechanism and adjust to the hang height you need on site.
Two kits to choose from: a four-bracket kit for 300×300, 300×600, 500×500 and 600×600 panels, and a six-bracket kit for 1200×300, 1200×600 and 1500×300 panels – the extra two brackets sit along the longer edges to stop the larger panel sagging in the middle.
The push-button release means dropping the panel for maintenance – or adjusting the hang height – takes seconds.
Key Features
- Hangs LED panels from fixed ceilings
- Two kits available (4 brackets, 4 wires) for 300x300, 300x600, 500x500 and 600x600 panels; and (6 brackets, 6 wires) for 1200x300, 1200x600 and 1500x300 panels
- Brackets fix using the panel's existing screw holes - no drilling into the panel
- Push-button wire release for fast install and easy maintenance access
- Adjustable hang height
- Compatible with LED Backlit Panels
Compatible with
What we get asked
What is an LED panel suspension kit?
An LED panel suspension kit hangs an LED panel from a fixed ceiling using brackets and wires, rather than dropping the panel into a suspended ceiling grid. The brackets fix to the back of the panel; the wires connect those brackets to the ceiling, so the panel hangs at whatever height you set.
When would I use a suspension kit instead of Z clips or grid mounting?
The right mounting depends on the ceiling:
- Suspended ceiling grid (T-bar) – drop the panel straight in, no clips or kits needed
- SS or burgess ceilings – use Z Clips to lock the panel into the concealed grid
- Plasterboard, exposed or any fixed ceiling without a grid – use this suspension kit to hang the panel from above
If you’re not sure which you’re working with, send us a photo and we’ll point you to the right product.
Which kit do I need - and what's in the bag?
Match the kit to the panel size:
- NET-43-16-04 – for 300×300, 300×600, 500×500 and 600×600 panels. In the bag: 4 brackets with push-button wire release (one per panel corner), 4 suspension wires, and wall plugs and screws for fixing the brackets to the ceiling
- NET-43-16-05 – for 1200×300, 1200×600 and 1500×300 panels. In the bag: 6 brackets (four at the corners plus two along the longer edges so the panel doesn’t sag in the middle), 6 suspension wires, and wall plugs and screws for fixing the brackets to the ceiling.
Each kit is self-contained – nothing extra to source for a standard install.
Which LumiRetro panels are these kits compatible with?
The kits are designed to fit our LED Backlit Panels. The brackets attach using the panel’s existing screw holes – so they only fit panels with those mounting points. If you’re working with a specific panel size and want to confirm, send us the part number.
Can the kits be used with other brands of LED panel?
We test the kits with our own LED Backlit Panels only – for a non-LumiRetro panel, give us a call and we’ll point you to a more general suspension solution.
How do I install the suspension kit?
Three steps:
- Remove the existing bracket fixing screws from the back of the panel, place each bracket over the screw holes, and re-attach the screws.
- Feed each suspension wire into a bracket and pull through until it locks against the bracket.
- Attach the other end of each wire to the top fixing bracket on the ceiling, then secure that bracket to the ceiling.
Can I take the panel down for maintenance after it's hung?
Yes. The push-button release on each bracket lets you free the wire – push the bottom of the bracket upwards and pull the wire downwards. The panel comes down without removing the brackets from the ceiling, so re-fitting is just feeding the wires back in. Useful for cleaning, accessing the void above the panel, or swapping a panel.
Do I need an electrician?
The suspension kit itself doesn’t require electrical work – it’s purely mechanical. The panel does: connecting it to the mains supply must be carried out by a qualified electrician in line with current wiring regulations. Most installs do both jobs together – hang the panel and wire it in at the same time.
What ceilings can I attach the kit to?
The top fixing bracket attaches to whatever ceiling you’ve got – plasterboard, exposed steel, timber – anywhere you can fix a suitable anchor that takes the panel’s weight. The kit includes wall plugs and screws as standard, suitable for plasterboard and most masrony.
What's the warranty on the suspension kit?
The suspension kit comes with a 3 year warranty.

